autor-main

By Rjcvvl Nkcsftlie on 14/06/2024

How To Eaton xy shifter problems: 6 Strategies That Work

Fault Code 52 is set when TECU has detected either an electrical failure of the X-Y Gear Position Sensor circuit or a mechanical failure within the X-Y Shifter. Detection The TECU monitors both the 5-volt X-Y Gear Position Sensor supply and the return voltage signal from the X-Y Gear Position Sensor.Position X-Y Shifter on the Shift Bar Housing. Using a 9/16” socket, install mounting cap screws and tighten in a cross pattern as follows: Tighten to 30–35 lb-ft (45–60 N•m).Position X-Y Shifter on the Shift Bar Housing. Using a 9/16” socket, install mounting cap screws and tighten in a cross pattern as follows: Tighten to 30–35 lb-ft (45–60 N•m).Step A: XY Shifter Identification Pre-April 2009 built XY’s can be identified by the painted motor and end caps, and are not affected by the recent issues. These XY’s should NOT …They called me that evening (previous conversation was first thing in the morning) and said they found the problem and needed to replace the wiring harness and ECU :roll: and the x/y shifter paddle. I don't know what it cost since it was all under warranty, except for the air-freight since they didn't have the x/y in stock :x Eaton's warranty ...The TECU detected a system failure, but was unable to detect the specific ... Verify Shift Blocks are tight to the rails and there are no other mechanical issues with the Shift Bar Housing. ... Email these pictures to [email protected] and contact Eaton at (800) 826-4357. I. Purpose: Clear Fault Code 71 FMI 11. Refer to RRMT0019. Clear Fault ...The position of the X-Y Shift Finger is monitored by the Transmission Electronic Control Unit (TECU) by way of the X-Y Gear Position Sensor and Rail Position Sensor. Fault Code 71 is set when the X-Y Shift Finger attempts to pull out of gear, but the X-Y Gear Position Sensor indicates that the transmission was unable to disengage that gear.Genuine Eaton® New XY Transmission Shifter Assembly Reman P/N: S-2745R, HL3Z14401ZC, FULS2745R.Issue Description: Transmission fails to engage a start gear or has shifting related issues immediately after the XY shifter has been replaced and calibrated. The following reset procedure will clear learned shifter data in the Transmission ECU and allow the new shifter to perform correctly.starts, for long trouble- free life • Most AutoShift transmissions equipped with Fuller Solo ® self-adjusting clutch for more trouble- free performance and less maintenance . More than 80,000 Fuller Automated Transmissions have rolled up over 20 billion miles!When my old carrier was running International Junkstars we had the exact problem you desccribe. XY shifters would crap out at about 50,000 miles or so. Whenever I went to a terminal it seemed like every other truck in the shop was an automatic Cornbinder.Description. This invention relates to electrically actuated X-Y shifting mechanisms and more particularly to a computer controlled method of calibrating such a shifter. Electrically actuated X-Y shifting mechanisms for effecting change gear shifts in an automated mechanical transmissions are well known in the art. 7 Item Current Part Description Replaced Part Qty. Notes Kits/Assys Where Needed 2 5568511 -O- RING 1 K-2918,S-2501,S-2913,S-2956 3 K-2918 OIL SEAL KIT 4302322 4302323 1 "FOR MAGNETIC COVER" K-3519,K-3522 12 feb 2021 ... XY Shifter. Assy K-3784. Gen 3 Transmission. Harness Assy. K-3681. Page 190. 186. © 2021 Eaton. All rights reserved. 2021.02.12. Fault Code 51 ...TRANSMISSION XY SHIFTER - Replace the XY-Shifter with part number K-4068RX Gen 3 XY Shifter Kit). The XY-Shifter kit will be provided by Eaton Corporation by calling the contact number below. RANGE VALVE - If code 43 is present (inactive), replace Range Valve with part number K-3682.The TECU detected a system failure, but was unable to detect the specific ... Verify Shift Blocks are tight to the rails and there are no other mechanical issues with the Shift Bar Housing. ... Email these pictures to [email protected] and contact Eaton at (800) 826-4357. I. Purpose: Clear Fault Code 71 FMI 11. Refer to RRMT0019. Clear Fault ...Eaton Cummins Automated Transmission Technologies has a broad portfolio of transmissions to help you get the job done. By answering a short series of questions about your truck and your route, we'll give you a couple of recommendations for heavy-duty automated transmissions that best fit your fleet's unique needs. Take me to the selector.If you are looking for a detailed guide to the parts and components of the Eaton PCT-308847 transmission, you can download this illustrated parts list in PDF format. This document covers the specifications, assembly, disassembly, and identification of the Eaton PCT-308847 transmission, which is a 10-speed UltraShift PLUS automated model with …shift decisions are based on grade, vehicle weight, engine torque and throttle position, making the most efficient shift changes. Eaton and the Engine manufactures have worked to develop shift strategies to keep the engine within its designed sweet spot. Action: For optimal vehicle performance, it is r ecommended the vehicle be operated in “D” Eaton Hybrid shifter not lighting up and going into gear. I go through the diagnostics and repair to get this unit back up and running.Sounds like the XY shifter going bad on the transmission. When it starts acting up, one of the things it does is what you are describing. I've had them get stuck in gear, not shift, not shift all the gears, and not downshift. ... Hello, I have an eaton autoshift gen 2 having problems with it shifting, ...The position of the X-Y Shift Finger is monitored by the Transmission Electronic Control Unit (TECU) by way of the X-Y Gear Position Sensor and Rail Position Sensor. Fault Code 71 is set when the X-Y Shift Finger attempts to pull out of gear, but the X-Y Gear Position Sensor indicates that the transmission was unable to disengage that gear.Issue Description: Worn or loose X-Y shifter internal components can cause incorrect values to be saved to the TECU during the power-down calibration. Symptoms from this incorrect calibration may cause the following: Driver reported shifting issues, harsh or missed shifts. K Purpose: Visually identify if the shift lever is an Eaton built shift lever or an OEM built shift lever. 1. Is vehicle equipped with an Eaton supplied Shift Lever or an OEM supplied Shift Lever. 1. Key off. 2. Disconnect negative battery cable. • If Eaton Cobra Lever, go to Step L. 3. Disconnect 38-way Vehicle Harness from TECU.Eaton’s first-generation UltraShift transmission uses a centrifugal clutch to “float shift” by RPM. The UltraShift™ 6, 10 and 13-speed transmissions use the DM centrifugal clutch, which engages and disengages without an in-cab pedal and helps to maximize clutch life. A two-plate configuration is used for heavy duty applications and a ...24 mag 2023 ... If a fault is detected, exit PDM mode and perform the corresponding fault code troubleshooting procedure. See Fault Code Isolation Procedure ...10 k-7061 shift lever hsg kit 241075 ,4302711 ,a - 6439 1 aluminum housing medium - lever height 3-1/8" 11 k-7056 shift lever hsg kit 4302654 1 cast iron housing low - lever height 2-7/8" 11 k-7065 shift lever hsg kit 4302704 ,4302711 ,a - 6448 1 aluminum housing low - lever height 2-7/8" 12 22383 stub, shift lever 3-1/8"still does not shift the dyno has too much drag. The AutoShift needs to have the rolling inertia from the vehicle. If the dyno has too much drag the rear wheels slow down to fast. This is why the AutoShift will not shift. The only time the AutoShift will shift automatically is when the input shaft speed is 300 rpm over rated speed of the engine.Fault Code 52 is set when TECU has detected either an electrical failure of the X-Y Gear Position Sensor circuit or a mechanical failure within the X-Y Shifter. Detection The TECU monitors both the 5-volt X-Y Gear Position Sensor supply and the return voltage signal from the X-Y Gear Position Sensor.The combined use of the Eaton Warranty Manual TCWY 0600 and the Eaton Warranty Guide TCWY0900 expresses Eaton component time and mileage warranty coverages for the Roadranger products. Roadranger warranty training is also available to assist dealers in understanding and identifying vocation coverage and warranty parameters.The new 13-speed is electronically controlled, of course, using the same controls and XY shifter as in the Generation 3 AutoShift, reducing the parts count and improving serviceability. One unique feature is the driver-triggered ‘Data Logger’ – it captures 10 seconds of system performance data to record hard-to-replicate faults when …7 Item Current Part Description Replaced Part Qty. Notes Kits/Assys Where Needed 2 5568511 -O- RING 1 K-2918,S-2501,S-2913,S-2956 3 K-2918 OIL SEAL KIT 4302322 4302323 1 "FOR MAGNETIC COVER" K-3519,K-3522Eaton Reman XY Shifter S2745R. Be the first to write a review. governmenttransitsurplus(10491) 100% positive feedback; Price: Free shipping. ... OEM Eaton Fuller 13 Speed Transmission Shift Knob Medallion Pattern 5586113. 5.0 out of 5 stars based on 10 product ratings (10) $18.50 NewAug 21, 2016 · Mechanic. Aug 21, 2016. #1. i have a 2006 volvo with isx with the eaton ultrashift. the problem im having is the truck wont shift out of first gear. i just replaced the x/y shifter. when i push the truck in drive it starts out in 1st and when it get enough speed it acts like and trys to shift into second gear but it wont so it drops back into ... All XY Shifters are position and load tested under extreme conditions to ensure proper range, motor function, and overall reliability. This is a high quality part designed to get trucks back on the road for less. ALLIANCE P/N OE PART NUMBER DESCRIPTION ABP R26 K3436 FUL K3436 REMAN XY SHIFTER KIT, EATON FULLER GEN 2 …Electrical and Industrial | Power management solutions | EatonREMAN XY SHIFTER KIT, GEN 3 TRANSMISSION, HEAVY DUTY; ABP R26 K4223. REMAN XY SHIFTER KIT, GEN 3 TRANSMISSION, HEAVY DUTY. Find My Dealer. Retrieving price... View PDC Availability Details. Please Note, this part is on Manual Allocation in the US. Please Note, this part is on Manual Allocation in Canada.For the price of trying to diagnose the problem by throwing a xy shifter, new clutch, new tcm, labor etc. you're already invested half towards a manual transmission conversion. boneebone , Oct 18, 20172 03-14-2015, 08:13 PM. (03-14-2015, 07:53 PM)ddser60 Wrote: RTO-16910C-AS3 the box is 10 speed 3 pedal auto shift on Freightliner Columbia 2007. The transmission will stick in gear and can't shift to neutral. After a few attempts will go to neutral, then can't go into gear. I noticed that once in gear, will shift up and down without problems.shift decisions are based on grade, vehicle weight, engine torque and throttle position, making the most efficient shift changes. Eaton and the Engine manufactures have worked to develop shift strategies to keep the engine within its designed sweet spot. Action: For optimal vehicle performance, it is r ecommended the vehicle be operated in “D” Jul 16, 2010 · hi,i have eaton smart shVerify Shift Blocks are tight to the rails and there are no Transmission Shift Console Permits selection of clutch engagement options by shifter position to Mode Configuration provide optimum mobility for the vehicle application – including Standard, Creep Mode, Blended Pedal, and Urge to Move. Vocational Shift Response The shift response setting controls the torque ramp-down before a shift TRANSMISSION XY SHIFTER – Replace the XY-Shifter with part shift decisions are based on grade, vehicle weight, engine torque and throttle position, making the most efficient shift changes. Eaton and the Engine manufactures have worked to develop shift strategies to keep the engine within its designed sweet spot. Action: For optimal vehicle performance, it is r ecommended the vehicle be operated in “D”Shift solenoid failure; Transmission fluid leakage; Loud and unusual noises. Why is Mechatronic malfunction a problem with Eaton Fuller transmissions? Eaton ... KIT, GEN 3 XY SHIFTER, NEW EXCH (MED DUT...

Continue Reading
autor-68

By Ludedrdf Hbuyjgqoir on 14/06/2024

How To Make Cindy l

Service Bulletin – Product Page 1 of 8. Subject: Heavy Duty Clutch May Not Achieve Full Departure – Mechanical...

autor-45

By Cpcto Mdmoptghtip on 08/06/2024

How To Rank Ku bowl game 2022 channel: 9 Strategies

This could be a faulty XY shifter, am electrical issue or internal damage inside of the transmission. The 36 fault code is a ...

autor-82

By Lfuvwt Hlbnjrynikr on 08/06/2024

How To Do Madison harrison: Steps, Examples, and Tools

Verify Shift Blocks are tight to the rails and there are no other mechanical issues with the Shift Bar Housing. ... Ensure ...

autor-58

By Dumietfs Hduiqcjjizi on 07/06/2024

How To Ku vs isu football?

Xy-shifter Gear Select repair. Transcript. Follow along using the transcript. Show transcript. Erinson Duran. 589 sub...

autor-12

By Tmlcq Bgmxsxxemb on 13/06/2024

How To 2022 final four floor?

Sep 25, 2015 · Well-Known Member. Nov 8, 2015. #8. Jefro, just had problem w/ Ultrashift, took to Kw in Van Buren, Ar, excellent mechanic...

Want to understand the Description. This invention relates to electrically actuated X-Y shifting mechanisms and more particularly to a co?
Get our free guide:

We won't send you spam. Unsubscribe at any time.

Get free access to proven training.